New Feature-  Bi-directional controls! These allow for electric fan control, transmission reset, and ESP shut-off on select vehicles.

The Interceptor gauge is 52mm (2 1/16") in diameter and will fit in all standard gauge pods of this size. A 5' cable is included with appropriate OBD2 connector. A splitter cable is included with the dual Interceptor units. A function menu is available by pushing both buttons simultaneously. One menu option allows you to enter a record mode. Once selected, the Interceptor will return to normal scan mode, but will start recording the displayed data automatically when the throttle exceeds 60%. Approximately 60 seconds of data will be stored. Returning to the menu screen, you can choose to replay the stored data on the Interceptor display. The gauge displays 2 parameters at a time, but can be programmed to cycle through up to 8 parameters during a user determined period of time. This way you can monitor several items without taking any other actions. High intensity LEDs can be used as shift lights or warning lights to indicate when a selected parameter exceeds an entered threshold. Due to the gauges extremely fast update rate, this light is very accurate and easy to set. Once you try it you'll find you can't live without it! Another menu option offers the ability to swap the foreground and backround colors of the display. Using this feature, for example, the gauge with a black backround and blue characters (negative image) becomes a blue backround with black characters (positive image). Not only can this be visually appealing but beneficial in changing lighting conditions. Positive images are easier to read in bright sunlight, negative at night. The Interceptor's scan rate can also be adjusted through a menu function. DTC's (Diagnostic Trouble Codes) can be accessed and cleared via menu options.This essential feature will help the gauge to pay for itself the first time the check engine light comes on. Those that have modified their vehicle will find this very handy when a sensor, vacuum line, etc. has been inadvertently left disconnected, or something was just not put back together properly. Click here for a list of SRT-4 diagnostic trouble code descriptions. The two analog inputs can be configured through menu choices. A linear conversion can be entered so that an analog signal connected to the gauge can be read in appropriate units. These inputs are handy for pressure signals such as those from MAP and oil pressure sensors, analog outputs from Air/Fuel ratio kits, etc. These signal can then be read and recorded along side the other parameters obtained on the vehicle's bus. The gauge has bi-directional controls allowing for manaul control of the low and high speed fans. On newer vehicles using the CAN bus (see application guide) the transmission controller can be reset to improve track performance. The Electronic Stability Program can also be completely turned off. Last but not least, the Interceptor will measure 0-60 times, as well as 1/8 and 1/4 mile time and speeds. This is accomplished through a simple menu selection. Installation is accomplished by simply plugging the supplied connector into the OBD2 port below the steering wheel. Literally plug-and-play!

Please note that because of the color combinations, many gauges are made to order and may take 3-5 days to ship!

Examples of Supported Parameters

RPM

MPH

Intake Air Temperature (post Intercooler)

Ambient Air Temperature (pre Intercooler)

Engine Coolant Temperature

Exhaust Gas Temperature (PCM Calculated)

Transmission Temp. (auto trans}

Manifold Pressure (vacuum/boost) displayed in PSI

Fuel Temperature

Battery Voltage

Battery Temp

Injector Pulse Width in msec.

Injector Duty Cycle (%)

Air Flow Rate into engine

Long Term Fuel Trim

Short Term Fuel Trim

O2 Sensor Voltage

Barometric Pressure

Ignition Advance

Base Spark

PCM Spark Adjust

Fuel Status (open/closed loop)

Wastegate Solenoid Duty Cycle (%)

Knock Retard

Knock Sensor Raw Voltage

Throttle Position Percentage

Throttle Position Sensor Raw Volts

Calculated Net Horsepower

Engine Load

Transmission Slip

Current Transmission Gear

Torque Delivered to Transmission

Torque Converter lockup status

Brake pressure

Brake Booster Travel

Steering Angle

Non-driven Wheel Speed

Lateral G's

Yaw

Fuel economy (instantaneous and average)

P-ratio - pressure ratio MAP/Barometer

2 user configurable analog inputs**

** 0-5v inputs can be configured to read the outputs from MAP sensors, Air/Fuel ratio kits, pressure or temperature sensors, etc. Raw voltage can be displayed or a conversion can be entered to read proper units. Users will find that ability to log RPM vs other parameters at high speed such as ignition advance, boost, or knock retard invaluable with regards to tuning.

Warranty

Aeroforce Technology warrants this product and its accessories against defects in material and workmanship for a period of 1 year from
the date of purchase.